Appearance Inspection Requirements for Integrated Circuit (CHI - ENG) 我們?yōu)槟硣壹墝嶒炇姨峁┘夹g(shù)類翻譯(中譯英),翻譯內容:集成電路外觀檢查要求。
譯文摘錄(保密內容以XXX替代):
4.4 外觀檢查過程器件的防護要求
a) 外觀檢查過程中必須采取防靜電措施。
b) 接觸器件時必須佩帶指套。
c) 外觀檢查過程中不得改變器件原包裝。器件檢查完畢后包裝應恢復到初始狀態,并注意上、下包裝的標志方向。
d) 外觀檢查過程中要輕拿輕放,防止器件跌落、碰傷、劃傷或晃動磨損。
4.4 Protection requirements for devices during appearance inspection
a) Anti-static measures must be taken during appearance inspection.
b) Fingerstall must be worn when touching the devices.
c) The original package of devices must not be changed during appearance inspection. After the completion of the device inspection, the package shall be restored to its original state, and the direction of signs of upper and lower packaging shall be noticed.
d) Handle devices gently during appearance inspection, and prevent the fall, bruise, scratch, shake or wear of devices.
4.5 外觀檢查環境條件
除非另有規定,應在進行外觀檢查的試驗室環境應滿足以下條件:溫度:20℃~28℃,相對濕度:30%~70%。
4.5 Environmental conditions for appearance inspection
Unless otherwise specified, the laboratory environment for appearance inspection shall meet the following conditions: Temperature: 20 °C to 28 °C, relative humidity: 30% to 70%.
4.6試驗實施
4.6 Test implementation
4.6.1器件包裝檢查
檢查器件的包裝是否為正確的包裝,包裝盒的方向是否正確。確認包裝完好并正確包裝后,接受器件外觀檢查工作。
4.6.1 Device packaging inspection
Inspect whether the packaging of devices and the direction of packing box are correct. After confirming that the package is intact and proper, appearance inspection of devices can be started.
4.6.2核對待外觀檢查器件
按照器件包裝標志的方向,在操作臺上打開包裝。核對待外觀檢查的器件,確認器件的型號、批號、數量與工序表一致。
4.6.2 Check the device to undergo appearance inspection
Open the package on the operating platform according to the direction of the device’s package sign. Check the device whose appearance is to be inspected and confirm that the model, lot number and quantity of the device are consistent with the operation list.
4.6.3外觀檢查
在到貨檢驗專用工作臺上,每次取出1只器件在光學顯微鏡下進行外觀檢查。若出現失效判據(見第4節)中的情況,則判器件為外觀檢查不合格品。發現器件外觀異?;蚨嘀黄骷庥^不合格時,填寫篩選問題報告。
4.6.3 Appearance inspection
On the special operating platform for arrival inspection, one device is taken out for appearance inspection under the optical microscope each time. In the event of a failure judgment (see Section 4), then the device is judged to be a non-conforming product in appearance inspection. When finding that the appearance of one device is abnormal or that of multiple devices is defective, fill out the screening problem report.
上一篇:2010-12-13 品格翻譯公司應環保部要求為其提供中挪項目申請背景報告翻譯,優質、高效的翻譯服務受到客戶高度評價。
下一篇:2010-12-06 品格為墨西哥某文化公司提供影視劇本翻譯服務。