亚洲色欲色欲www,精品久久亚洲中文无码,午夜做爰xxxⅹ性高湖视频美国,藏獒又硬又粗进去好爽a片免费

譯文摘錄：

AAAA Flange Facer

AAAA法蘭銑刀盤

General Information
基本信息

* Use of large, heavy duty, construction grade bearings provides powerful, rigid
performance throughout the entire machine facing range, even machining over
bolt hole patterns
•使用大型、重型、結構級軸承，在設備整個銑削范圍內提供強大的硬性性能,即使對螺栓孔進行銑削也可發揮良好性能。

* Infinitely variable feed rates from 0.002-0.035”/rev (0.051-0.889 mm / rev)
provide operational flexibility and the ability to provide phonographic finishes with
OFF/ON capabilities
• 進刀速度可在0.002到0.035英寸/圈（0.051-0.889毫米/圈）之間無限變化，使設備的操作具有靈活性，并可使用開/關迅速進行表面處理。

* Tool head can be rotated a full 360? providing the ability to create a variety of
chamfers, O-Ring grooves, lens rings and other angular surfaces as needed
• 刀架可進行360度旋轉，這樣可根據需要?jiǎng)?chuàng)造各種倒角、O型環凹槽、透鏡環和其他斜面。

* Oversized ring gear provides steady rotation for difficult machining challenges
• 超大的環形齒輪可使設備在進行有難度的銑削作業時穩定回轉。

* Unique chucking system minimizes parts and greatly simplifies machine set-up and tear down
• 獨特的夾具系統可使工作量達到最小化，并極大簡化設備組裝和拆卸過程。

* Chucking system can be removed to allow customers to face mount the flange facer for applications like machining heat exchanger flanges
• 夾具系統可以拆卸，這樣客戶就可以根據用途安裝法蘭銑刀盤，例如銑削熱交換器的法蘭盤。

* Turning arm can be infinitely positionedreduce rotating swing clearance as needed for close quarter applications
• 近距離銑削時，車削臂可以盡可能減少回轉間隙。

* Feed box can be mounted to provide either radial or axial feed
• 可安裝進刀箱，以提供徑向和軸向進刀功能。

* Features a remote control feed rate adjustment to allow the machine operator to safely adjust the feed rate without reaching into the rotating machine. This also allows for feed adjustment while machining
•進刀速度可遙控調整，這樣操作者可在不靠近正在轉動的設備的情況下,安全地調整進刀速度?？梢栽阢娤鬟^程中調整進刀速度。

Adjusting the Radial Slide Anti-Backlash Lead Nut
調整徑向滑動消隙螺母

The radial slide lead nut is adjustable to provide near zero backlash. Adjustment of the lead nut is done by one M4 set screw on each of the two lead nuts.
調節徑向滑動消隙螺母可將縫隙調整至近乎為零。螺母的調整可通過兩個螺母之間的那一個M4定位螺釘完成。

Adjustment should only be necessary after many hours of use. These should only be adjusted if the machine is no longer producing a good finish.
設備運行數小時后，才有必要進行調整。僅在設備無法繼續保持其最佳性能時進行調整。

If the slide is visibly loose and causing machining problems, tighten the two set screws by small increments until less than .001” of the backlash can be measured.
如果滑塊可見明顯松動，并導致加工問題，那么輕輕緊固兩個定位螺釘，直至測得縫隙尺寸小于0.001英寸。

After adjustment, check travel over the full length of leadscrew for tight spots.
調整完成后，檢查導螺桿全長的沖程。

Machining Arm
加工臂

The machining arm is infinitely adjustable for versatile positioning and to clear obstructions.
加工臂可無限進行調節，進行任何定位，以應對任何加工問題。